ISO 3795 — Standard

About the Standard

Scope title: burn rate of interior trim materials

ISO 3795 is a standard published by International Organization for Standardization (ISO). The international standards organisation; it publishes the widest body of management system, test method and product standards.

See the other 310 codes from ISO

Coverage areas

Fire Testing — What Does This Testing Field Cover?

The section below describes the field that code ISO 3795 belongs to; it is not the text of the standard or the regime itself. The scope title of the code is given above, and technical requirements are shared at the quotation stage.

Fire testing measures two different concepts, and confusing them is the most common mistake in the field. REACTION to fire describes how much a material contributes to the start and growth of a fire. RESISTANCE to fire is the ability of a building element to hold a fire back for a defined period. One is a material property, the other a property of an element.

On the reaction side, ignitability, flame spread, heat release, smoke production, flaming droplets and toxic gas release are measured. The result is translated into an EN 13501-1 class in Europe, ASTM E84 indices in North America and a UL 94 class for appliance plastics. These three systems cannot be converted into one another; their scales and set-ups differ.

On the resistance side, furnace tests are carried out. The element is exposed to a defined temperature-time curve and it is measured how long it maintains three functions: load bearing (R), integrity (E) and insulation (I). For a fire door, the designation EI 60 says the element maintains its integrity and insulating function for sixty minutes.

SCALE is decisive in this family and directly affects cost. Small flame tests are suitable for screening materials and are fast and inexpensive. But real fire behaviour changes with scale: a material that self-extinguishes on a small specimen may sustain a flame over a large surface. Large-scale set-ups such as the room corner test and full-scale facade tests are therefore indispensable in critical applications.

Facade systems have become the most sensitive subject in the field in recent years. The rapid spread of facade fires in tall buildings has led national regulations to require large-scale facade testing. What is assessed here is not a single material but the SYSTEM: insulation, cladding, air cavity, fixings and fire barriers are tested together.

Smoke and toxicity form a separate body of work, because most deaths in a fire are caused by smoke rather than flame. In rail systems and on ships, smoke density and gas toxicity measurements are mandatory items; in an enclosed space the time available for evacuation depends on these values.

Cables have a sub-body of their own. A cable bundle inside a building can form a serious path for fire to spread between floors; flame spread, smoke production, halogen content and circuit integrity are therefore assessed for cables under separate standards, and in Europe the EN 13501-6 classification is used.

Method groups in this field

Non-combustibility and calorific value
The EN ISO 1182 non-combustibility furnace and EN ISO 1716 gross calorific value; the determinants of classes A1 and A2.
Single burning item (SBI)
EN 13823; heat release, flame spread and smoke production are measured together in a medium-scale corner set-up.
Small flame
Ignitability with a single flame source to EN ISO 11925-2; UL 94 horizontal and vertical burning; needle flame and glow wire.
Cone calorimeter
ISO 5660 / ASTM E1354; heat release rate, total heat release and smoke production are measured. The most informative test in material development.
Fire resistance
Furnace tests with the standard temperature-time curve; separate set-ups for doors, walls, floors, glazing and service penetrations.
Large scale
Room corner test (ISO 9705, NFPA 286), facade fire tests and vertical flame spread tests on cable bundles.
Smoke and toxicity
Optical smoke density, smoke gas analysis and toxicity indices; mandatory in rail systems and marine.

Commonly confused in this field

Reaction to fire and resistance to fire are different concepts; the specification must be explicit about which is required.
UL 94, ASTM E84 and EN 13501-1 results cannot be converted into one another.
A small-scale result is not evidence of large-scale behaviour; large-scale testing is required in critical applications.
A class is valid together with the end-use installation of the product; a different substrate or air cavity changes the result.
For facade systems a result for a single material is not sufficient; the system must be tested as a whole.
The fire class of a product does not show the fire resistance of an assembly made from it.

Which decisions these results support

The fire class in the declaration of performance for construction products
Regulatory compliance in the selection of cables, flooring and interior linings
Approval of interior materials for rail vehicles, ships and aircraft
Approval of the facade system design
Meeting insurance and project specification requirements

Structure of the Code

Published by: ISO
Serial number: 3795
Part: without partition

Codes in the library without release year is kept. The current version changes over time; If the year is specified in your specification, that version is taken as basis, if not specified, the most current version is applied.

Scope

Related Tests and Services

A separate test page based on this code has not yet been released. The code falls within the scope of the following test families.

Technical Requirements

Standard texts are copyright of the relevant organization; test condition, sample and acceptance criteria cannot be fitted here.

Technical requirements specific to your product, once we clarify the scope At offer stage shared in writing.

Relevant Product Groups and Legislation

This code is included in the standard tag of the product pages below.

These product pages carry notes for the following markets: European Union, United Kingdom, USA. Whether the standard is mandatory in the relevant market varies depending on the product group and the applicable legislation.

Regulations published with this code on the same product pages:

(AB) 2018/858Vehicle Type-Approval FrameworkApproval of motor vehicles and their components. Component and separate technical unit approval run under this framework; the E mark arises from it.
UNECEUNECE 1958 AgreementType-approval under component-specific UNECE regulations (e.g. R10 EMC, R30/R54 tyres, R43 glazing).
UNECE R10UNECE R10Electromagnetic compatibility approval for vehicles and their components.
2011/65/EURoHSRestriction of hazardous substances in electrical and electronic equipment.
2000/53/ATELVEnd-of-life vehicles. Sets heavy-metal restrictions and recoverability targets.
(EU) 2017/745MDRThe Medical Device Regulation. Classification (I, IIa, IIb, III), clinical evaluation, technical documentation and post-market surveillance obligations; the notified body's role grows as the class rises.
(EU) 2017/746IVDRThe In Vitro Diagnostic Medical Devices Regulation. In vitro diagnostic devices fall under this regulation instead of the MDR.
(AB) 2017/745 art. 33EUDAMEDThe European medical device database. From 28 May 2026, the actor registration, UDI/device, certificate and market surveillance modules are mandatory; placing on the market is not possible without a valid SRN.
2006/42/ATMachinery Directive (overlap)Relevant essential requirements also apply to medical devices that also qualify as machinery.
(EC) 1907/2006REACHRegistration, evaluation, authorisation and restriction of chemicals; SVHC notification.
(EU) 2023/1230Machinery RegulationReplaces 2006/42/EC and becomes mandatory on 20 January 2027 with no further transition period. Requires notified-body involvement for Annex I high-risk machinery.
2014/35/EULVDThe Low Voltage Directive. Governs electrical safety in the 50–1000 V AC range.
2014/30/EUEMCThe Electromagnetic Compatibility Directive. Emission and immunity are covered together.
2014/34/ABATEXEquipment and protective systems used in explosive atmospheres. The category and conformity route are determined by zone classification.
2000/14/ATNoise EmissionNoise emitted into the environment by outdoor equipment. Machinery within scope requires a sound-power-level declaration and marking.
2014/68/EUPEDThe Pressure Equipment Directive for pressurised parts; the category is determined by pressure and volume.
(EU) 2024/573F-GasRefrigerant type, GWP value and leak-tightness obligations for systems containing a refrigerant.
(AB) 547/2012Ecodesign (water pumps)Ecodesign requirements for water pumps. Sets minimum efficiency index and product-information requirements.
(AB) 2019/1781Ecodesign (electric motors)Efficiency class requirements for electric motors and variable-speed drives.
(AT) 1935/2004Food Contact MaterialsGeneral requirements for equipment in contact with food; material conformity is required for valves in food lines.
(AB) 2020/2184Drinking Water Contact ProductsHygiene requirements for materials in contact with water under the Drinking Water Directive.
2014/29/ABSimple Pressure VesselsA separate directive for series-produced simple pressure vessels; its scope must be distinguished from the PED.
2010/35/ABTransportable Pressure EquipmentThe pi mark and periodic inspection regime for transportable pressure equipment.
2009/48/ECToy SafetyThe Toy Safety Directive. Regulates mechanical, physical, flammability, chemical and electrical safety requirements together; a technical file and safety assessment are mandatory.
EN 62115Electrical toysSafety for electric toys; applies to mains-connected or battery-powered toys.
(AT) 1907/2006 Annex XVII item 51-52Phthalate RestrictionRestriction of certain phthalates in toys and childcare articles.
(EU) 2023/1542Batteries RegulationBattery obligations and a removability requirement for toys containing a battery.
(AB) 1007/2011Textile LabellingTextile fibre names and labelling. Declaration of fibre composition and regulation of the label language.
(AT) 1907/2006 Annex XVII item 43Azo Dye RestrictionRestriction of certain azo dyes in textiles in contact with skin.
(AB) 2019/1021PFAS / PFOA RestrictionRestriction of PFOA and its derivatives under the Persistent Organic Pollutants Regulation.
(EU) 2023/988GPSRThe General Product Safety Regulation. The safety framework for consumer products not covered by sector-specific legislation.
(EU) 2016/425Personal Protective Equipment (overlap)The PPE Regulation's scope and category are determined for textiles with a protective function.
(AB) 10/2011Plastics in Food ContactPlastic materials in contact with food. The list of authorised substances, and overall and specific migration limits.
(AT) 2023/2006Good Manufacturing PracticeGood manufacturing practice (GMP) for food-contact materials.
(AB) 2025/40Packaging and Packaging WasteThe Packaging and Packaging Waste Regulation. Recyclability, recycled-content and packaging-reduction obligations; replaces 94/62/EC.
(AB) 2022/1616Recycled PlasticRecycled plastic materials in contact with food.
(EU) 2024/3110Construction Products RegulationDeclaration of performance and CE marking for construction products. Most provisions apply from 8 January 2026; it progressively replaces (EU) 305/2011.
(AB) 305/2011CPR (transition)Continues to apply during the transition period for product groups where a new harmonised standard has not been published.
EN 13501-1Reaction-to-Fire ClassificationReaction-to-fire class for construction products; a mandatory item of the declaration of performance.
(EU) 2023/1115Deforestation (wood-based)A deforestation-free supply declaration for wood and derived construction materials.
(AT) 1223/2009Cosmetic Products RegulationThe Cosmetic Products Regulation. Appointing a responsible person, the product information file (PIF), the safety assessment (CPSR) and CPNP notification are mandatory; there is no product approval, and responsibility rests with the manufacturer.
(AT) 1223/2009 Annexes II-VIProhibited and Restricted SubstancesLists of prohibited substances, restricted substances, and permitted preservatives, colorants and UV filters.
(AT) 1223/2009 art. 16Nanomaterial NotificationA separate notification six months before placing on the market for products containing nanomaterials.
(AT) 1223/2009 art. 18Animal Testing BanA ban on animal testing of finished products and ingredients, and on placing animal-tested products on the market.
(AT) 178/2002General Food LawThe general principles of food law, traceability and food safety responsibility.
(AT) 852/2004Food HygieneHygiene rules for food businesses and the obligation for a HACCP-based system.
(AB) 1169/2011Food Information to ConsumersFood labelling; nutrition declaration, allergen information and origin information.
(AB) 2023/915ContaminantsMaximum levels of contaminants in food.
(AT) 396/2005Pesticide residuesMaximum residue limits in food of plant and animal origin.
(AT) 2073/2005Microbiological CriteriaMicrobiological criteria for foodstuffs.

Related Standards

Frequently Asked Questions

Is this standard mandatory for my product?

Whether it is mandatory depends on the product group, the target market and the applicable legislation. Once you tell us your product and market, we clarify in writing whether this standard is required.

How long does the test process take?

Duration depends on the scope of the standard, the number of specimens and current capacity. The exact duration is shared, together with the specimen and scope details, at the quote stage.

Do you issue certification against this standard?

Which activity is carried out under which accreditation scope is separately confirmed at the application stage. Up-to-date scope information is published on our corporate page.

What happens if the standard I need is not here?

The library is based on a continuously growing inventory. If you cannot find the code you are looking for, you can send it through the quote form; we will assess the relevant scope and get back to you.