About the Standard
Scope title: requirements for safety footwear
EN ISO 20345 is a standard published by European Standard (EN) (EN). Standards published by the European standardisation organisations and adopted as national standards in member states; they are used as harmonised standards under EU directives.
See the other 194 codes from ENCoverage areas
Footwear and Leather Testing — What Does This Testing Field Cover?
The section below describes the field that code EN ISO 20345 belongs to; it is not the text of the standard or the regime itself. The scope title of the code is given above, and technical requirements are shared at the quotation stage.
Footwear and leather testing assesses the physical durability and chemical safety of a product together. Footwear is a MULTI-COMPONENT product: the sole, upper, lining, insole, heel and bonding line are tested both individually and together. One component being good does not mean the product is good; failure usually appears where components join.
On the physical side, the most common field failure is SOLE-UPPER SEPARATION. Bond strength is therefore the most critical measurement in the field and is a direct indicator of the bonding process (surface preparation, adhesive selection, pressing conditions). Next come sole abrasion and flex resistance: a shoe is flexed hundreds of thousands of times over its life.
Slip resistance is the most important parameter for safety and its measurement depends on the surface: wet ceramic, oily steel and dry floor give different results. Slip resistance is therefore reported not as a single number but with the surface and the direction of slip stated.
A separate body of work applies to protective footwear, and this is the most commercially critical distinction. Toe protection (impact and compression), penetration resistance, antistatic behaviour, heat and cold insulation, electrical insulation and fuel resistance are assessed under personal protective equipment requirements. CE is mandatory for these products and the category must be chosen correctly; an ordinary footwear test report does not satisfy that file.
On the chemical side, CHROMIUM (VI) has a special place in leather. The chromium (III) used in tanning can oxidise into chromium (VI) during storage and ageing; that is, a leather that was compliant at production may exceed the limit months later. The time of measurement and the history of the sample therefore affect the result, and measurement after ageing may be required.
Other chemical items are aromatic amines from azo dyes, pentachlorophenol, short-chain chlorinated paraffins, dimethyl fumarate and phthalates. These items come from REACH restrictions and brand restricted substance lists.
There is NO CE marking on consumer footwear; the obligation runs through material composition labelling, compliance with chemical restrictions and general product safety. Labelling has a rule of its own: the type of material used for the upper, the lining and insole and the outer sole is shown by pictograms.
Comfort and functional claims (waterproofness, moisture management, breathability) are supported by separate tests, and these claims require evidence if used in marketing copy.
Method groups in this field
Bonding and strength
Sole-upper bond strength, seam strength, heel attachment strength, strap and buckle strength.
Abrasion and flexing
Sole abrasion, flex resistance (dry and at low temperature), insole abrasion.
Slip resistance
Forward and backward slip measurements on wet ceramic, oily steel and dry floor.
Protective properties
Toe impact and compression resistance, penetration resistance, antistatic behaviour, heat and cold insulation, fuel and chemical resistance.
Leather chemistry
Chromium (VI), azo dye amines, pentachlorophenol, short-chain chlorinated paraffins, pH and fat content.
Comfort and function
Waterproofness, water vapour permeability, moisture management, colour fastness and the effect of perspiration.
Commonly confused in this field
- Footwear claiming a protective function falls under PPE legislation and requires CE; a consumer footwear test report does not satisfy that file.
- A chromium (VI) result depends on the age of the sample and its storage conditions; leather compliant at production may exceed the limit later.
- Slip resistance is not a single number; it cannot be interpreted without stating the surface and the direction.
- A result obtained for one component does not cover the whole product; the joints are tested separately.
- Labelling rules run on material pictograms; an incorrect pictogram causes problems in customs and market surveillance.
- A waterproofness claim is not verifiable unless the test used and the number of flex cycles after which it was measured are stated.
Which decisions these results support
- Compliance with the brand restricted substance list
- The PPE category and CE file for protective footwear
- Supplier and lot-based acceptance control
- Root cause analysis of field complaints (bond opening, sole separation)
- Substantiation of functional claims
Structure of the Code
- Published by
- EN ISO
- Serial number
- 20345
- Part
- without partition
Codes in the library without release year is kept. The current version changes over time; If the year is specified in your specification, that version is taken as basis, if not specified, the most current version is applied.
Scope
Related Tests and Services
A separate test page based on this code has not yet been released. The code falls within the scope of the following test families.
Technical Requirements
Standard texts are copyright of the relevant organization; test condition, sample and acceptance criteria cannot be fitted here.
Technical requirements specific to your product, once we clarify the scope At offer stage shared in writing.
Relevant Product Groups and Legislation
This code is included in the standard tag of the product pages below.
These product pages carry notes for the following markets: European Union, United Kingdom, USA. Whether the standard is mandatory in the relevant market varies depending on the product group and the applicable legislation.
Regulations published with this code on the same product pages:
- (AB) 1007/2011Textile LabellingTextile fibre names and labelling. Declaration of fibre composition and regulation of the label language.
- (EC) 1907/2006REACHRegistration, evaluation, authorisation and restriction of chemicals; SVHC notification.
- (AT) 1907/2006 Annex XVII item 43Azo Dye RestrictionRestriction of certain azo dyes in textiles in contact with skin.
- (AB) 2019/1021PFAS / PFOA RestrictionRestriction of PFOA and its derivatives under the Persistent Organic Pollutants Regulation.
- (EU) 2023/988GPSRThe General Product Safety Regulation. The safety framework for consumer products not covered by sector-specific legislation.
- (EU) 2016/425Personal Protective Equipment (overlap)The PPE Regulation's scope and category are determined for textiles with a protective function.
Other Adoptions of the Same Number
This number is also published by other bodies. Adoptions may carry a national annex; the code named in your specification is the one required.
Related Standards
Frequently Asked Questions
Is this standard mandatory for my product?
Whether it is mandatory depends on the product group, the target market and the applicable legislation. Once you tell us your product and market, we clarify in writing whether this standard is required.
How long does the test process take?
Duration depends on the scope of the standard, the number of specimens and current capacity. The exact duration is shared, together with the specimen and scope details, at the quote stage.
Do you issue certification against this standard?
Which activity is carried out under which accreditation scope is separately confirmed at the application stage. Up-to-date scope information is published on our corporate page.
What happens if the standard I need is not here?
The library is based on a continuously growing inventory. If you cannot find the code you are looking for, you can send it through the quote form; we will assess the relevant scope and get back to you.