About the Standard
Scope title: mandrel bend flexibility of coatings
ASTM D522 is a standard published by ASTM International (ASTM). It publishes material, product and test method standards; it is the body most often turned to in corrosion, mechanical and materials testing.
See the other 199 codes from ASTMCoverage areas
Paint and Coating Testing — What Does This Testing Field Cover?
The section below describes the field that code ASTM D522 belongs to; it is not the text of the standard or the regime itself. The scope title of the code is given above, and technical requirements are shared at the quotation stage.
Paint and coating testing measures the adhesion of a coating to the surface, its mechanical durability and its resistance to environmental effects. Because a coating is a thin layer, the results depend both on the material and on the QUALITY OF APPLICATION; the same paint gives an entirely different result over a different surface preparation.
This dual dependence is the most important knowledge in the field. A coating failure usually arises not from the paint itself but from the surface preparation: oil residue, insufficient roughening, an oxide layer or moisture. Coating tests therefore assess not only the product but also the process, and the results are used for process control.
COATING THICKNESS is a recurring variable in the field. Many durability results relate directly to thickness; a thin area becomes the starting point of corrosion. Thickness measurement is therefore reported routinely alongside the other tests and is usually taken at several points — thickness falls at edges and corners, especially on complex geometries.
Three approaches are used on the adhesion side, each giving different information. The tape test is fast and suitable for field use but is a coarse scale. The cross-cut test shows behaviour at the intersections of layers. The pull-off method produces a numerical strength value and is the most suitable for comparison.
On the mechanical side, flexibility (mandrel bending), impact resistance, hardness, abrasion and stone chip resistance are measured. Stone chipping has a special place in automotive: gravel striking the coating under real road conditions is simulated, and the result is assessed according to whether the coating continues to protect the base metal.
On the appearance side, gloss and colour difference are monitored NUMERICALLY. Colour is assessed with a colour measuring instrument rather than by eye and the colour difference is expressed as a number; this makes it possible to compare different lots and different suppliers.
On the durability side, accelerated ageing (xenon arc, fluorescent UV), humidity, condensation and salt spray are applied. The result is assessed with scales for blistering, rusting, creep from a scribe and loss of adhesion; these scales are defined in separate standards and the report must state which was used.
In industrial processes such as powder coating and electrophoretic coating, the curing cycle (temperature and time) is what determines the result. An under-cured coating looks good but has poor chemical resistance and adhesion; oven profile measurement is therefore part of coating quality control.
Method groups in this field
Thickness
Dry film thickness by magnetic and non-magnetic methods; multi-point measurement and assessment of the distribution.
Adhesion
Tape test, cross-cut test and pull-off adhesion strength.
Mechanical strength
Mandrel bend flexibility, rapid deformation (impact), pencil and scratch hardness, Taber abrasion, stone chipping.
Appearance
Gloss measurement, colour difference calculation, orange peel and surface defect assessment.
Environmental durability
Salt spray, humidity, condensation, xenon arc and fluorescent UV ageing, chemical and stain resistance.
Assessment scales
Scales for blistering, degree of rusting, creep from a scribe and loss of adhesion.
Commonly confused in this field
- A coating result depends on the surface preparation; even if the paint itself is good, a poor preparation gives a poor result.
- A durability result without a reported thickness cannot be compared.
- The tape test is a coarse scale; numerical comparison requires the pull-off method.
- Colour cannot be assessed by eye; numerical colour difference measurement is required.
- An ageing result without a stated assessment scale cannot be interpreted.
- If the curing cycle is incomplete the coating looks good but its durability is poor; the oven profile is part of quality control.
Which decisions these results support
- Paint system approval and supplier selection
- Process control of the paint line and lot acceptance
- Supporting outdoor and automotive durability claims
- Detecting defects arising from surface preparation
- Monitoring colour and gloss consistency lot by lot
Structure of the Code
- Published by
- ASTM
- Serial number
- D522
- Part
- without partition
Codes in the library without release year is kept. The current version changes over time; If the year is specified in your specification, that version is taken as basis, if not specified, the most current version is applied.
Scope
Related Tests and Services
A separate test page based on this code has not yet been released. The code falls within the scope of the following test families.
Technical Requirements
Standard texts are copyright of the relevant organization; test condition, sample and acceptance criteria cannot be fitted here.
Technical requirements specific to your product, once we clarify the scope At offer stage shared in writing.
Related Standards
Frequently Asked Questions
Is this standard mandatory for my product?
Whether it is mandatory depends on the product group, the target market and the applicable legislation. Once you tell us your product and market, we clarify in writing whether this standard is required.
How long does the test process take?
Duration depends on the scope of the standard, the number of specimens and current capacity. The exact duration is shared, together with the specimen and scope details, at the quote stage.
Do you issue certification against this standard?
Which activity is carried out under which accreditation scope is separately confirmed at the application stage. Up-to-date scope information is published on our corporate page.
What happens if the standard I need is not here?
The library is based on a continuously growing inventory. If you cannot find the code you are looking for, you can send it through the quote form; we will assess the relevant scope and get back to you.